Sunflower seed shell pellet mill is appropriate for crude fibre compression forming, such as: maize straw, peanut shell, rice husk, corncob, cotton seed hull, wheat-straw, sunflower seed shell, sawdust, cotton stalk, weeds, etc. all kinds of agricultural straws, house refuse, waste plastic and wastes in factory. It is also suitable for raw materials which are difficult to form with low bonding ratio. Furthermore, organic bacterial manure, organic fertilizer and compound fertilizer are applicable to pelletize under low temperature.
Main Pelletizing Parts of Sunflower Seed Shell Pellet Mill:
1. Pelleting system: the eccentric shaft is supported by bearing and safety device. On the left is a pair of roller equipped on the eccentric shaft. The nip between rollers and the die can be regulated by adjusting the 4 nuts on the two long bolts. Specifically, the distance (also the nip) shall remain at 0.1mm to 0.3mm.
2. Reduction box: equipped with a pair of gear. When the main motor starts, driving force will be transferred to the main shaft via the coupling, featuring lower noise and less vibration. The ring die tightened on the end of the main shaft by the hold hoop will gyrate following the shaft. (biomass pellet mill is driven by V-belt directly for a larger production yield.)
3. Press rollers: the rollers are sitting on the eccentric shaft via a bearing respectively and the bearing can be lubricated through the central oil duct connected directly with the backside grease pump for continuously periodic lubrication during pelletizing. Bearings are sealed up at both ends of the eccentric shaft. The housing of the shaft is also forged with high quality alloy steel and advanced heat treatment for better working performance.
4. Ring die (also called the mold as key component of a biomass pellet mill) counts most in the pelletizing process. There are plenty of aligned pores on it forming a honeycomb zone which is the pellet forming area. Forged by using high quality alloy steel (high-chromium stainless steel alloy) and also thanks to the state of the art heat treatment, the die boasts super high hardness, strength and good wear-resistant property, producing pellets with diameter ranging from 2.5mm to 12mm to meet the clients’ requirements (Generally biomass pellets are with the universally acquiescent diameter of 6mm or 8mm).
Welcome to contact or visit Fote Machinery: info@sinoftm.com
Main Pelletizing Parts of Sunflower Seed Shell Pellet Mill:
1. Pelleting system: the eccentric shaft is supported by bearing and safety device. On the left is a pair of roller equipped on the eccentric shaft. The nip between rollers and the die can be regulated by adjusting the 4 nuts on the two long bolts. Specifically, the distance (also the nip) shall remain at 0.1mm to 0.3mm.
2. Reduction box: equipped with a pair of gear. When the main motor starts, driving force will be transferred to the main shaft via the coupling, featuring lower noise and less vibration. The ring die tightened on the end of the main shaft by the hold hoop will gyrate following the shaft. (biomass pellet mill is driven by V-belt directly for a larger production yield.)
3. Press rollers: the rollers are sitting on the eccentric shaft via a bearing respectively and the bearing can be lubricated through the central oil duct connected directly with the backside grease pump for continuously periodic lubrication during pelletizing. Bearings are sealed up at both ends of the eccentric shaft. The housing of the shaft is also forged with high quality alloy steel and advanced heat treatment for better working performance.
4. Ring die (also called the mold as key component of a biomass pellet mill) counts most in the pelletizing process. There are plenty of aligned pores on it forming a honeycomb zone which is the pellet forming area. Forged by using high quality alloy steel (high-chromium stainless steel alloy) and also thanks to the state of the art heat treatment, the die boasts super high hardness, strength and good wear-resistant property, producing pellets with diameter ranging from 2.5mm to 12mm to meet the clients’ requirements (Generally biomass pellets are with the universally acquiescent diameter of 6mm or 8mm).
Welcome to contact or visit Fote Machinery: info@sinoftm.com