SMALL RICE MILLING LINE: After the feed, adjust the feed device, so that the flow is stable and stable along the width of the screen surface, the flow should not exceed the rated amount of ± 10%, not suddenly large and small; production voltage changes, it should be adjusted Into the damper, stable air volume, to ensure that the stone effect; adjust the air volume, so that rice in the screen surface or to the slate was loose suspended state, the suspension height of about 30-40 mm; to stone screen, uniform plate and into the door to keep.
SMALL RICE MILLING LINE: If not smooth, timely clean up; use two to stone, to ensure that the stone to achieve the following requirements: the first stone to the sand with rice, per kilogram of rice does not exceed 50; the second to the valley without sand, Net Valley with side by side stone should not exceed 1 / kg, two to stone efficiency of 95% or more; stop, should stop the feed, then close the stone machine and fan, and finally close the damper.
SMALL RICE MILLING LINE: 4 Hulling check the roller at both ends of the fastening screws are loose, whether the size of the head and nails or hard objects embedded, static balance correction, adjust the appropriate pressure.
SMALL RICE MILLING LINE: Start the equipment, to be empty after the normal operation of the feed; calibration pressure to ensure that the shelling rate, rice husking rate should be 80-85%, and check the hull off the shelling rate and broken rice content is in line with the requirements;
SMALL RICE MILLING LINE: Check the feed gate, if the debris obstruction, should be cleared to ensure that the normal flow to the length of each rubber roller contact with the length of 80-100kg per hour is appropriate; operating procedures if the phenomenon of abnormal, should be adjusted Operation or downtime inspection; in case of sudden stop in production, should check whether the feed gate is automatically closed, the roller is automatically released. And then boot, the roller should be retained on the rice removed, and to be empty after the normal operation, and then into the rice.
SMALL RICE MILLING LINE: 5 Valley rough separation check whether the layers of chaff ash accumulation, the screen surface is smooth; check the screen surface inclination is appropriate.
SMALL RICE MILLING LINE: Start the equipment, to be empty after the normal operation, and then feed; adjust the material flow, to maintain uniform and stable, the central surface layer of the screen surface control in the 15 mm or so; start the roughing machine should be the first flow after the flow is uniform and The separation of layers separates the quality of each layer.
Small Rice Milling Line
SMALL RICE MILLING LINE: If not smooth, timely clean up; use two to stone, to ensure that the stone to achieve the following requirements: the first stone to the sand with rice, per kilogram of rice does not exceed 50; the second to the valley without sand, Net Valley with side by side stone should not exceed 1 / kg, two to stone efficiency of 95% or more; stop, should stop the feed, then close the stone machine and fan, and finally close the damper.
SMALL RICE MILLING LINE: 4 Hulling check the roller at both ends of the fastening screws are loose, whether the size of the head and nails or hard objects embedded, static balance correction, adjust the appropriate pressure.
SMALL RICE MILLING LINE: Start the equipment, to be empty after the normal operation of the feed; calibration pressure to ensure that the shelling rate, rice husking rate should be 80-85%, and check the hull off the shelling rate and broken rice content is in line with the requirements;
SMALL RICE MILLING LINE: Check the feed gate, if the debris obstruction, should be cleared to ensure that the normal flow to the length of each rubber roller contact with the length of 80-100kg per hour is appropriate; operating procedures if the phenomenon of abnormal, should be adjusted Operation or downtime inspection; in case of sudden stop in production, should check whether the feed gate is automatically closed, the roller is automatically released. And then boot, the roller should be retained on the rice removed, and to be empty after the normal operation, and then into the rice.
SMALL RICE MILLING LINE: 5 Valley rough separation check whether the layers of chaff ash accumulation, the screen surface is smooth; check the screen surface inclination is appropriate.
SMALL RICE MILLING LINE: Start the equipment, to be empty after the normal operation, and then feed; adjust the material flow, to maintain uniform and stable, the central surface layer of the screen surface control in the 15 mm or so; start the roughing machine should be the first flow after the flow is uniform and The separation of layers separates the quality of each layer.
Small Rice Milling Line